Home Customer support center

Documentation 7

• User Manual
• Safety Information
• Datasheet
• Leapfrog Motor Control Board (LMC) V3, Bolt Pro
• Quick start Guide

See all 7 articles

Maintenance 12

• Calibrating Bed and Printheads
• Maintenance Schedule
• Clogged Printhead Hardware Checklist
• Replacement: E3D V6 Hot End
• BuildTak Surface Replacement

See all 12 articles

Firmware 2

• Update Machine Firmware (Motor Control Board) Bolt Pro
• Update Machine (UI) Software V1.3.2

Repair Instructions 13

• Replacement: X-motor/endstop Cables
• Replacement: Printhead Internal Tubing
• Replacement: Printhead PCB
• Replacement: Printhead Cable Chain
• Replacement: E-Motor (Printhead Extrusion)

See all 13 articles

3D Models 8

• Filament pressure thumbscrew Gauge
• Fan duct
• Filament waste bucket
• Printhead Glands
• Transportation Belt Clamp

See all 8 articles

Software 4

• Simplify3D Print Settings (.FFF)
• Printing Modes: Normal / Sync mode / Mirror mode Simplify3D
• Cura Download
• Cura - Leapfrog Bolt (PRO) - Custom FFF printer

Spare Parts Bolt (Pro) 1

• Order spare parts

Documentation 5

• User Manual
• Safety Information
• Datasheet
• Layout of the Xeed Electronics
• Hot End - Version Guide

Maintenance 9

• Calibrating the Z Offset
• Replacement: Hot End
• Adjustment: Z-sensor probe / solenoid
• Connecting to the WIFI network
• How to: open up the printhead

See all 9 articles

Firmware 2

• Firmware Update (Motor Control Board) Xeed
• Software Update (User Interface) Xeed

Repair Instructions 12

• Replacement: Timing Belts
• Replacement: Printhead Fans
• "Low Disk Space" Error
• "Black Screen/White Cursor" Error
• "503 Service Unavailable" Error

See all 12 articles

3D Models 2

• Test print for bed calibration
• ABS test prints

Software 2

• Simplify3D Print Settings (.FFF)
• How to Configure Cura - Leapfrog Xeed 3D Printer

Spare Parts Xeed 1

• Order spare parts

Documentation 5

• User Manual
• Safety Information
• Datasheet
• Layout of the Creatr HS Series Electronics
• Hot End - Version Guide

Maintenance 10

• Calibrating the print bed on the Creatr HS (XL)
• Cleaning the print bed
• Cleaning the extruders
• Calibrating the hot ends
• Calibrating offset between extruders on the Creatr HS (XL)

See all 10 articles

Firmware 4

• Software Re-install (User Interface)
• Firmware Update (Motor Control Board) Creatr HS (XL)
• Firmware archive Creatr HS (XL)
• Software Update (User Interface) Creatr HS (XL)

Repair Instructions 39

• Print Head Stops Mid-Print: M999 - Checking the Thermistor and Ribbon Cable - Creatr HS
• Replacement head fans
• How to Install, Repair, or Replace the (Flexible) Filament Gland
• How to Calibrate the Z-Offset of the Creatr HS
• Why is My Creatr HS not Connecting to My PC?

See all 39 articles

3D Models 1

• Fan duct

Software 39

• Simplify3D - Print settings for the Creatr HS
• Simplify3D - Print settings for the Creatr HS XL
• Materialise - Creatr 2.1.0 Creatr (HS)
• Simplify3D - Print settings for the Creatr HS Lite
• Cura - How to Configure Cura - Leapfrog Creatr HS 3D Printer

See all 39 articles

Spare Parts Creatr HS (XL) 1

• Order spare parts

Documentation 5

• User Manual
• Datasheet
• The Layout for the Creatr Series Motherboard
• Serial Number - Guide
• Hot End - Version Guide

Maintenance 7

• Unclog the hot ends
• Calibrating hot ends
• Calibrating offset between hot ends on the Creatr (XL)
• Calibrating print bed
• Adjusting belt tension

See all 7 articles

Firmware 7

• Firmware archive Creatr (XL)
• Firmware: how to upload to Creatr (XL)?
• Installing the Creatr Drivers
• Which firmware version does your motorcontrolboard currently have?
• Firmware: which version do I need for my Creatr (XL)?

See all 7 articles

Repair Instructions 17

• How to Replace the Y-Axis Stepper Motor
• Why is my printing head moving in one direction only?
• How to replace the motherboard on your Leapfrog Creatr 3D printer.
• Common mistake with replaced motherboard on the Creatr (XL)
• How to Check the Function of the X and Y Stepper Motors on My Leapfrog Creatr 3D Printer

See all 17 articles

3D Models 0

Software 5

• Materialise Creatr 2.1.0 Software and Voucher
• How to Configure Cura - Leapfrog Creatr 3D Printer
• Simplify3D - How to configure Simplify 3D for my Leapfrog 3D printer
• Simplify3D - User Manual for Creatr
• Simplify3D - Configuration Parameters and Scripts Leapfrog Creatr

Spare Parts Creatr (XL) 1

• Order spare parts

Documentation 2

• Leapfrog ONE brochure
• Leapfrog ONE product presentation

Maintenance 0